Here's some more of Johns plated parts....Ian

email (option): ian@wright52.plus.com

Ian, I love the attention to detail on your BSA, it looks amazing. Can I ask what treatment you use on your alloy components; engine, gearbox & carb? I'd like to get the same finish on my G3WO. Also, what type of paint do you use?


Thanks,

Tom

Thanks for the positive comment....All the various alloy components are prepared by hand to remove obvious damage and then bead blasted using a medium aluminim oxide grit (80 grit) followed by finishing glass bead...
The oxide I run at about 85 psi and the finishing glass bead (which I recall is a 60 grit) I run at about 60-65 psi...I do a lot of preparation before blasting and getting the right finish on the castings prior to blasting is the 'trick'...Contact me off forum if you want more information on that subject...

I've always mixed my own paint to achieve the 'KGP No3' type shade I like....I use late war British Dark Olive Drab and mix with red oxide primer to move the colour towards the brown/green colour of KGP....All the paints are synthetic...I spray it myself using a Devilbiss spray gun...I've achieved pretty good results with the 'bottom of the range' 'Finishline' gun...I worked on the theory that even the base line Devilbiss gun has good nozzle technology and the baseline part is just a less fancy finish and construction...I use one gun for primer applications and another for top coat...One other gun I keep for 'civvy' jobs to apply laquer coats....Ian

email (option): ian@wright52.plus.com

Thanks Ian, I always like looking at bikes that you and Ron post on here, it gives me something to aim for! Do you do anything the stop the alloy components oxidising after you've cleaned them? The alloy still looks nice and bright on your carb and cases.

Tom what year/contract is your G3? my 1940 panel tank had all painted cases. Fortunately I have the parts list for my contract, which lists all the finishes. Ron

%%htmlItem_1%%

email (option): ronpier@talk21.com

After blasting and washing/cleaning the parts thoroughly to remove any blasting media I just apply some WD40 and wipe off with a clean rag/paper towel....Ian

email (option): ian@wright52.plus.com

Easy way to "dull" stainless is to use a domestic chemical stainless steel saucepan cleaner .
The trick is to do one and time it so that you get the finish you find appealing
The longer the solutions are on the duller and darker the parts get

I haven't had a chance to compare with vapour blasting, but have used brick cleaner (hydrochloric acid) with good results. As WM20 says, parts get darker with longer exposure.

Hi Ron, my G3WO is frame number is 13596, which I think is 1940. I don't have the Orchard/Madden book to hand to check what contract it is. I've seen an ex-works photo of a non-panel tank and all the alloy is bare unpainted.

Sorry, don't mean to hijack the thread.

Regards,

Tom

Hi Tom 13596 is the 597th bike from 3000 under contract C8078 supplied in 1941. 256 of them had panel in tank (I guess the first 256?)

Apart from the parts list for my earlier contract, I have these factory pictures of a later non panel bike, which shows the gearbox is painted but not the engine. It also shows a different silencer. But I've no idea of the contract that this bike comes from. Ron

%%htmlItem_1%%

email (option): ronpier@talk21.com

An add on to a wavering thread...
Does anyone know the original finish of early front brake rods? Were all parts plated or some painted? I'm sorting out a list for plating, while the UK still has an economy.🙄

most of the pictures I've looked at, they look painted, which is how I've done mine. Ron

%%htmlItem_1%%
%%htmlItem_2%%

email (option): ronpier@talk21.com

Hi Craig
I have the colours & finish for the rods & by part
It was a mix of plate & paint
I can check tomorrow- the book is not here with me in the house
Br
John

email (option): jonnyob1@googlemail.com

Here's another picture (I'm sure there are clearer ones) The only plated parts look like the sliding part at the top. Divert your eyes to the right of the bare metal speedo drive in the brake plate. Ron

%%htmlItem_1%%

email (option): ronpier@talk21.com

Another good picture from John O'Brien, Ron

%%htmlItem_1%%

email (option): ronpier@talk21.com

Even better! Cheers John!

Ron
%%htmlItem_1%%

email (option): ronpier@talk21.com