Questions? Looking for parts? Parts for sale? or just for a chat,

The WD Motorcycle forum

WD Motorcycle forum
Start a New Topic 
Author
Comment
What electronic regulator shell I purchase?

My dynamo is the E3LM type; what electronic regulator is recommended?
Where to buy? Any other info I need to know?
Thanks – Michael.

email (option): michasteinmann@gmail.com

Re: What electronic regulator shell I purchase?

Michael I have used the units made by Al Osborne and fitted into MCR1 regulators several times over the years and never had a problem. Try his site for information and advice. http://www.aoservices.co.uk/

Ron

email (option): ronpier@talk21.com

Re: What electronic regulator shell I purchase?

Michael
My dynamo is the E3LM type; what electronic regulator is recommended?
Where to buy? Any other info I need to know?
Thanks – Michael.
[/quote]

Michael.

The best electronic regulator on the market at the moment is the DVR2 from Dynamo regulators Ltd, It will fit inside your existing regulator box & this unit is the only electronic regulator I know that will actually charge a flat battery, but let him know whether it is pos or neg earth. Give Mike a call on 01489 880552, he is very helpful.

Kind regards TTJohn

email (option): Jomichael@aol.com

Re: What electronic regulator shell I purchase?

Hi,
I think that the DVR2 from Dynamo regulators Ltd
Is the same as the DVR2 from Manor thech' which is very good.
http://www.manortec.co.uk/dvr.htm

I fitted one easily into an old original Lucas.
When I fitted it, I measured, and it gave a super steady 7.2V.

I just gave it way few days ago Micha.
If you contacted me, it was yours..
Nevermind..
Anyway, it is recommended.
Noam.

%%htmlItem_1%%

%%htmlItem_2%%

email (option): noam10@gmail.com

Re: What electronic regulator shell I purchase?

TTJohn


The best electronic regulator on the market at the moment is the DVR2 from Dynamo regulators Ltd, It will fit inside your existing regulator box & this unit is the only electronic regulator I know that will actually charge a flat battery, but let him know whether it is pos or neg earth. Give Mike a call on 01489 880552, he is very helpful.

Kind regards TTJohn [/quote]

If the others wont charge a flat battery what possible use are they?

Re: What electronic regulator shell I purchase?

I would not presume to say that one is better than another unless I had first hand knowledge of any problems. I only say what know.
I am running an AO unit on my Indian special which is coil ignition and therefore relies on a battery. I am running a 1940's Miller dynamo with two 5 amp Cyclon gel batteries wired in series to give 10 amps. So far, so good.

Ron

email (option): ronpier@talk21.com

Re: What electronic regulator shell I purchase?

Thank you all very much.

Re: What electronic regulator shell I purchase?

Keith H
TTJohn


The best electronic regulator on the market at the moment is the DVR2 from Dynamo regulators Ltd, It will fit inside your existing regulator box & this unit is the only electronic regulator I know that will actually charge a flat battery, but let him know whether it is pos or neg earth. Give Mike a call on 01489 880552, he is very helpful.

Kind regards TTJohn [/quote]

If the others wont charge a flat battery what possible use are they? [/quote]

Keith.
Most electronic regulators will not charge a battery that has gone flat, I have tried several different types including K tec etc, DVR2 will, tried and tested.

TTJohn

email (option): Jomichael@aol.com

Re: What electronic regulator shell I purchase?

I have an Al Oz unit on my Norton rigid single with no problems after 2 years and plenty of miles. My mate has one on his ES2 which has done 7,000 miles and survived some clumsy miss-wiring.

Re: What electronic regulator shell I purchase?

Keith H

If the others wont charge a flat battery what possible use are they? [/quote]

Hi Keith,

Yes, not only most of the electronic units would not charge a flat batt,
It is also not allowed to use it with no battery or a "dead" (not charging) one.

The electronic unit needs the voltage and load on the batt/output side,
In order to function, much like an alternator on any car.

If used with no load, the output power is being built on the
Regulator's transistors, and with no load to spill it onto,
It boils itself.

Once or twice, when I had no other option, as I had a flat batt at night, I run
It with lights on, as a load and the regulator survived.

If it happens at daytime, it is best to pull the dynamo connectors
(F+D split bullet) till obtaining a reasonably good batt..

Noam.

email (option): noam10@gmail.com

Re: What electronic regulator shell I purchase?

Thanks for that Noam
I'm glad I havn't yet given up on the old mechanical ones since I had a John Gardner unit fry itself due to a faulty dynamo back in the late 70s.

Re: What electronic regulator shell I purchase?

Hello,

my recommendation is:
http://www.laubtec.de/
Advantage:
- adjustable voltage output to suit Sulphur acid as well as NiCd batteries
- fits in the original box
- sent with installation plan, and really easy to install

I run ( my WD16H ) negative earth with 2 sealed lead batteries from Amazon which are just 5.40€ each, and have in total 8Ah.
Works great.

Good luck
Heiko

email (option): hfr@gmx.info

Nieuwe pagina 1