Andy.... Ainsley says we settled on 57%. There will always be vibration, but this gave me the most comfortable setting. My WD/CO and WD/G are both fitted with the dome top pistons from Hitchcock's. These raise the compression from 6.1-1 to 7.1-1. But yours seems to go well enough with however your engine is configured.:+1: Ron
BSA singles of the era use 58%..I've always used 60% after picking up the figure from a well known BSA builder in my area back in the 70s...I've had good results with that...I think a figure in that area is a safe bet for an engine where the factor is unknown...Single cylinder engines are inherently out of balance and will always vibrate, it can only be moved to an area of the rev range which is not used frequently...
It can be made a lot worse by omitting the head steady or running with it loose as it is an integral part of the triangulation of the frame/engine assembly....Badly worn engine plate holes and studs can also have an effect...These things change the frequency at which the engine vibrates 'in sympathy' with the frame...Ian
Yes Ian, Ainsley balanced my crank to 60% but it was horrible. So I removed and stripped it again and he moved it to 57%. Which I'm more than happy with. The engine had new mains and big end and one of the Bullet dome top pistons, which was a different weight to the original. (I think it was heavier??) I have the tool for aligning the main bearing races.
These RE's don't have a head steady and with no spec written down it was all a bit guesswork. Ron
Thanks for info Ron ....very helpful. I have read about the main bearing tool
....just wondered why this is needed as surely the positioning of the races is fixed by the machined positions in the cases??...or am I missing something ?
I thought that as well...If the register between the two halves of the crankcase is machined at the same time as the bearing housings and the cases are a good fit together, then the bearings are bound to be in line..That is the method employed on BSA engines and they are good enough to mix crankcase halves without problems....Ian
The tool is to make sure that the races are pressed in parallel to each other. I also wondered about that myself, but my mate made me the tool so I used it. Ron
Ian, Andy, out of interest, here is the details about the main bearings. Since I was trying to eliminate anything that might aid vibration, I went ahead according to the book. It more than likely made no difference though? Ron
To me it reads like it's an aid to an unskilled fitter who may not push the bushes in square.
I try to "idiot proof" as much as I can.
(especially for me)
Andy.... Ainsley says we settled on 57%. There will always be vibration, but this gave me the most comfortable setting. My WD/CO and WD/G are both fitted with the dome top pistons from Hitchcock's. These raise the compression from 6.1-1 to 7.1-1. But yours seems to go well enough with however your engine is configured.:+1: Ron
The reason I was looking at this Ron is because on the the recent Worcsetershire Rally my WD/CO developed a new and quite loud mechanical noise from the engine. It sounded quite disconcerting...further investigation has revieledthat bizarrley it was mostly the decompressor shaft vibrating against the exhaust tappet and the the alloy cover..you would not think something so small could make a noise so loud...fixed it by putting a very small rubber o ring in the recess in the alloy tappet cover to "wedge" the shaft in place !!
Ha Ha Well done Andy. A rubber O ring was a cheaper fix than a total strip and new main bearings....You just need to nail that exhaust pipe on better.:hammer_and_wrench: Ron
Never really had this engine apart... I suppose I really should but scared to look! Runs ok though even if its not as quiet mechanically as yours. As long as it lasts another 3 or 400 miles I will be OK :smiley: ....The exhaust has been well and truley fixed curtesy of the correct stud and shouldered nut from Hitchcocks !!